AEG Refrigerator 72358 KA3 User Manual

SANTO 72358 KA3  
Electronic Refrigerator  
Operating Instructions  
818 35 69-02/2  
 
Contents  
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5  
Environmental Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6  
Appliance Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7  
Before Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Installation Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
Appliance Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9  
The Refrigerator needs Ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Installation of the carbon filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10  
Electrical Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11  
Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12  
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Buttons for Adjusting the Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13  
Temperature Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
COOLMATIC button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14  
Quick chill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
ALARM OFF button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15  
Prior to Initial Start–Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Initial Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Temperature Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16  
Switching the Appliance off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17  
Holiday Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Opening the Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18  
Control and Information Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
"Open Door" Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Temperature warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
Function Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19  
818 35 69-02/2  
3
 
Contents  
Interior Fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Storage Shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Variable Inner Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Salad Bin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20  
Bottle Rack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Quick Chill Shelf . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21  
Bottle and Can Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Dismantling of the Bottle and Can Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Bottle Holder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22  
Proper Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23  
Hints and Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Normal Operating Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Food Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Energy Saving Advice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24  
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Maintenance and Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Internal Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
External Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25  
Changing the carbon filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
Replacing the Light Bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26  
What to do if ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27  
Regulations, Standards, Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Technical Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29  
Guarantee Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30  
Service & Spare Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31  
4
818 35 69-02/2  
 
1Important Safety Instructions  
These warnings are provided in the interests of your safety. Ensure  
that you understand them all before installing or using this  
appliance. Your safety is of paramount importance. If you are unsure  
about any of the meanings of these warnings contact the Customer  
Care Department.  
Prior to Installation  
• Check the refrigerator for transport damage. Under no circumstances  
should a damaged appliance be installed! In the event of damage,  
please contact your retailer.  
Installation  
• This appliance is heavy. Care should be taken when moving it.  
• It is dangerous to alter the specifications or attempt to modify this  
product in any way.  
• Ensure that the appliance does not stand on the electrical supply  
cable. If the supply cable is damaged, it must be replaced by a cable  
available from your local Service Force Centre.  
• Make sure that the power plug is not squashed or damaged by the  
back of the appliance. A damaged power plug may overheat and  
cause a fire.  
• If the power plug socket is loose, do not insert the power plug. There  
is a risk of electric shock or fire.  
• Any electrical work required to install this appliance should be carried  
out by a qualified electrician or competent person.  
• Parts which heat up should not be exposed. Whenever possible, the  
back of the appliance should be close to a wall, but leaving the  
required distance for ventilation, as stated in the installation  
instructions.  
• The appliance should be left for 2 hours after installation before it is  
turned on, in order to allow the refrigerant to settle.  
Refrigerant  
The refrigerant isobutane (R600a) is contained within the refrigerant  
circuit of the appliance, a natural gas with a high level of  
environmental compatibility, which is nevertheless flammable.  
• During transportation and installation of the appliance, be certain  
that none of the components of the refrigerant circuit become  
damaged.  
818 35 69-02/2  
5
 
Environmental Information  
• If the refrigerant circuit should become damaged:  
– avoid open flames and sources of ignition;  
– thoroughly ventilate the room in which the appliance is situated.  
Child Safety  
• Do not allow children to tamper with the controls or play with the  
product.  
• Keep packaging material away from children! (There is a risk of  
suffocation!)  
During Use  
• This appliance is designed for domestic use only, specifically for the  
storage of edible foodstuffs only. It is not intended for commercial or  
industrial use.  
• Containers with flammable gases or liquids can leak at low  
temperatures. Do not store any containers with flammable materials  
such as, spray cans, fire extinguisher refill cartridges etc in the  
refrigerator.  
• Manufacturers´ recommended storage times should be adhered to.  
Refer to relevant instructions.  
Maintenance and Cleaning  
• Before cleaning, always switch off the appliance and disconnect from  
the electrical supply.  
• When unplugging always pull the plug from the mains socket, do not  
pull on the cable. Damage to the cord may cause a short circuit, fire  
and/or electric shock.  
Servicing  
• This product should be serviced by an authorised engineer and only  
genuine spare parts should be used.  
• Under no circumstances should you attempt to repair the appliance  
yourself. Repairs carried out by inexperienced persons may cause  
injury or serious malfunctioning. Contact your local AEG Service  
Force Centre.  
Environmental Information  
2 Packaging material  
The packaging materials are environmentally friendly and can be recy-  
cled. The plastic components are identified by markings, e.g. >PE<,  
>PS<, etc. Please dispose of the packaging materials in the appropriate  
container at your local waste disposal facilities.  
6
818 35 69-02/2  
 
2 Old appliance  
The symbol W on the product or on its packaging indicates that this  
product may not be treated as household waste. Instead it shall be  
handed over to the applicable collection point for the recycling of elec-  
trical and electronic equipment. By ensuring this product is disposed of  
correctly, you will help prevent potential negative consequences for the  
environment and human health, which could otherwise be caused by  
inappropriate waste handling of this product. For more detailed infor-  
mation about recycling of this product, please contact your local city  
office, your household waste disposal service or the shop where you  
purchased the product.  
When disposing of your old appliance:  
Make the appliance unusable by cutting off the cable and remove any  
door catches to ensure small children cannot be trapped inside.  
Help to keep your country tidy - use an authorised disposal site.  
Appliance Transport  
Two persons are required for transport of the appliance. There are two  
recessed handles at the front of the base and at the back of the  
appliance at the top for improved gripping.  
0 1. Grip the appliance with the recessed handles positioned as in the draw-  
ing, and transport the appliance.  
2. In order to push the appliance into its final position, press carefully at  
the top of the door and tip the appliance back slightly. The weight is  
then transferred to the back wheels and the appliance can be easily  
pushed.  
818 35 69-02/2  
7
 
Before Use  
Packaging  
0 1. Remove all adhesive tape and packaging from the interior of the appli-  
ance.  
Any remnants of adhesive can be removed with white spirit.  
3
2. Remove the transport protection pieces and pull off the adhesive tape.  
3. Wash the inside of the appliance with lukewarm water with a little  
bicarbonate of soda added (5 ml to 0.5 litre of water). Do not use soap  
or detergent as the smell may linger. Dry the appliance thoroughly.  
Remove the transport fittings from  
the storage shelves:  
4. Slide the fittings securing the shelf  
forward to the thicker section on  
the edge of the storage shelf.  
5. Slide the storage shelf far enough  
forward so that it can be hinged  
downwards and the fittings can be  
removed from the guides.  
8
818 35 69-02/2  
 
Installation  
The position of the freezer part and the fridge part in the combination  
fridge-freezer can be decided by the customer. However the final  
assembly of the appliance or a later change in the position of the  
freezer and fridge must be carried out by your local Service Force  
Centre.  
Installation Location  
The appliance should be installed in a well ventilated, dry room.  
Energy use is affected by the ambient temperature.  
The appliance should therefore  
– not be exposed to direct sunlight;  
– not be installed next to radiators, cookers or other sources of heat;  
– only be installed at a location whose ambient temperature  
corresponds to the climate classification, for which the appliance is  
designed.  
The climate classification can be found on the rating plate, which is  
located at the left on the inside of the appliance.  
The following table shows which ambient temperature is correct for  
each climate classification:  
Climate classification  
for an ambient temperature of  
SN  
N
+10 to +32 °C  
+16 to +32 °C  
+18 to +38 °C  
+18 to +43 °C  
ST  
T
Appliance Alignment  
0 1. The appliance must be level, please compensate for unevenness in the  
floor by turning the two adjustable feet at the front.  
818 35 69-02/2  
9
 
Installation  
The Refrigerator needs Ventilation  
Air is fed under the door through the vent  
slots in the base and is exhausted upwards  
along the back wall. To ensure proper air  
circulation never cover or alter the vent  
openings.  
Important! If the appliance is installed under  
a hanging cabinet, a clearance of at least 10  
cm between the top of the appliance and the  
cabinet above it must be maintained.  
Please check whether, after installing your  
appliance and especially after reversing the  
door, the door seal fits tightly. A badly fitting  
door seal may lead to heavy frosting and a  
higher power consumption (see also "What to  
do if ...“).  
Installation of the carbon filter  
On delivery the carbon filter is placed  
in a plastic bag to ensure the length of  
life of the carbon filter. The filter  
should be placed behind the grill  
before the cabinet is turned on.  
0
1. The cover can be opened by simultane-  
ously pressing the lever on the right of  
grill (1) and pulling the cover outward  
(2).  
2. The carbon filter is then mounted in  
the slot found in the back of the cover  
(3).  
The filter should be handled carefully  
so fragments don´t loosen from the  
surface.  
1
10  
818 35 69-02/2  
 
Installation  
Electrical Connection  
Any electrical work required to install this appliance should be carried  
out by a qualified electrician or competent person.  
WARNING – THIS APPLIANCE MUST BE EARTHED  
The manufacturer declines any liability should these safety measures  
not be observed.  
1
Before switching on, make sure the electricity supply voltage is the  
same as that indicated on the appliance rating plate. The rating plate is  
inside, on the left.  
The appliance is supplied with a 13 amp plug fitted. In the event of  
having to change the fuse in the plug supplied, a 13 amp ASTA  
approved (BS 1362) fuse must be used.  
Important  
The wires in the mains lead are coloured in accordance with the  
following code:  
Green  
Green and Yellow Earth  
& Yellow  
Blue  
Neutral  
Live  
Brown  
As the colours of the wires in the  
mains lead of this appliance may  
not correspond with the coloured  
markings indentified in the terminals  
of your plug, proceed as follows:  
Brown  
Blue  
1. The wire coloured green and  
yellow must be connected to the  
terminal marked with the letter  
“E“ or by the earth symbol or  
coloured green and yellow.  
Cord Clamp  
2. The wire coloured blue must be connected to the terminal “N“ or  
coloured black.  
3. The wire coloured brown must be connected to the terminal marked  
“L“ or coloured red.  
4. Upon completion there must be no cut, or stray strands of wire  
present and the cord clamp must be secure over the outer sheet.  
Warning! A cut-off plug inserted into a 13 amp socket is a serious  
safety (shock) hazard. Ensure that the cut-off plug is disposed of safely.  
1
818 35 69-02/2  
11  
 
Description of the Appliance  
View of the appliance  
á Control panel  
à Butter and cheese compartment with lid  
â Door storage compartments  
ã Bottle compartment  
å Salad bin  
ç Shelves  
é Quick chill shelf  
è Filter housing  
ê Bottle and can holder  
Bottle rack  
ë
Rating plate  
í
12  
818 35 69-02/2  
 
Description of the Appliance  
Control Panel  
1
2
3
4
5
6
7
8
ON/OFF button  
Button for adjusting the temperature (for warmer temperatures)  
Temperature display  
Button for adjusting the temperature (for colder temperatures)  
COOLMATIC indicator light (yellow)  
COOLMATIC button  
Warning indicator light (red)  
ALARM OFF button (see „Control- and Information Systems“)  
Buttons for Adjusting the Temperature  
The temperature is adjusted using the  
„+“ (WARMER) and „-“ (COLDER) buttons.  
These buttons are connected to the temperature display.  
• The temperature display is switched over from the display of the  
ACTUAL temperature (Temperature display is illuminated) to the  
display of the DESIRED temperature (Temperature display flashes) by  
pressing one of the two buttons, „+“ (WARMER) or „-“ (COLDER).  
• Each time one of the two buttons is pressed again the DESIRED tem-  
perature is adjusted by 1 °C.  
• If neither button is pressed, the temperature display automatically  
switches back after a short period (approx. 5 sec.) to the display of  
the ACTUAL temperature.  
DESIRED temperature means:  
The temperature that is required in the freezer compartment, this can  
be adjusted to the temperatures shown in the display. The DESIRED  
temperature is indicated by flashing numbers.  
ACTUAL temperature means:  
The temperature display indicates the temperature that is currently  
present in the freezer compartment. The ACTUAL temperature is  
indicated with illuminated numbers.  
818 35 69-02/2  
13  
 
Description of the Appliance  
Temperature Display  
The temperature display can indicate several pieces of  
information.  
• During normal operation, the temperature currently present in the  
refrigerator (ACTUAL temperature) is displayed.  
• When the temperature is being adjusted a flashing display indicates  
the fridge compartment temperature currently set (DESIRED temper-  
ature).  
• If there is a fault in the appliance the temperature display shows a  
square in the temperature display for the fridge.  
COOLMATIC button  
The COOLMATIC function is suited for quick cooling of  
large quantities of goods in the refrigerator, e.g. drinks  
and salads for a party.  
0 1. The COOLMATIC function is switched on by pressing the COOLMATIC  
button. The yellow light illuminates.  
The COOLMATIC function now provides for intensive cooling. A DESI-  
RED temperature of +2 °C is automatically selected. The COOLMATIC  
function is ended automatically after a period of 6 hours. The originally  
selected DESIRED temperature is again valid. The temperature display  
shows the ACTUAL refrigerator temperature.  
2. The COOLMATIC function can be ended manually at any time by press-  
ing the COOLMATIC button again. The yellow light goes out.  
Important! Once the COOLMATIC function has been switched on the  
DESIRED temperature that was set originally cannot be changed.  
14  
818 35 69-02/2  
 
Description of the Appliance  
Quick chill  
The quick chill function can be used for the fast cooling of drinks in  
cans or bottles in the fast cool storage tray or of larger amounts of  
room-temperature food. The built-in charcoal filter reduces the  
development of any smell.  
Chilling of cans/bottles  
Place cans or bottles in the holder on  
the quick chill shelf in front of the fan  
grille. Turn the fan regulator to maxi-  
mum and press the COOLMATIC button.  
The yellow indicator light comes on.  
Chilling of food  
Place the food in the fridge. Open the fan regulator to maximum and  
press the COOLMATIC button. The yellow indicator light comes on.  
When the drinks or the food is sufficiently cooled, press the COOLMATIC  
button again. The yellow indicator light goes out. Set the fan regulator to  
the minimum position.  
When this function has been activated, forced air will chill the groce-  
ries, and the temperature in the cabinet reset to +2 °C. After 6 hours  
the COOLMATIC function is ended automatically. The yellow light goes  
out. Turn the air regulator to its minimum position.  
3
ALARM OFF button  
With the ALARM OFF button, the acoustic warning signal  
can be switched off, e.g. the "Open Door" warning when  
sorting in or out, the food to be chilled.  
818 35 69-02/2  
15  
 
Prior to Initial Start–Up  
Before connecting the appliance to the mains and putting it into  
1
operation for the first time, leave the appliance to stand for 30 minutes  
if was transported upright. After transport on its side, the appliance  
must be left to stand for 2 hours before putting it into operation. This is  
necessary to allow the refrigerant to flow back into the compressor.  
Otherwise the compressor may be damaged.  
0 1. Please clean the appliance interior and all accessories prior to initial  
start-up (see section: “Maintenance and Cleaning”).  
2. The appliance must be correctly installed in accordance with the chap-  
ter "Installation" before it is put into operation for the first time. Care  
should be especially taken that the mains voltage and frequency avail-  
able correspond with the appliance’s rating plate.  
Initial Start-Up  
0 1. Insert plug into mains socket.  
2. Press ON/OFF button.  
The compressor starts and then runs automatically.  
3. Set temperature to +5 °C or colder (see section: "Temperature Adjust-  
ment").  
Goods to be refrigerated can be loaded immediately after switching on,  
because the storage temperature in the refrigerator is quickly reached.  
3
Temperature Adjustment  
With the buttons for temperature adjustment the desired temperatures  
in the refrigerator can be adjusted.  
0 1. Press either the „+“ (WARMER) or „-“ (COLDER) button.  
The temperature display switches over and the DESIRED temperature  
currently set flashes on the temperature display.  
2. To adjust to a warmer temperature, press the „+“ (WARMER) button. To  
adjust to a colder temperature, press the „-“ (COLDER) button. The  
changed setting is immediately displayed on the temperature display.  
Each time the button is pressed the temperature is adjusted by 1 °C.  
Adjustable temperature range: +2 °C to +8 °C, +15 °C (Holiday mode)  
16  
818 35 69-02/2  
 
Note: From a food safety point of view, +5 °C for the refrigerator  
compartment should be considered cold enough as a storage  
temperature.  
When the buttons are not further pressed after an adjustment has been  
made, after a short period (approx. 5 sec.) the temperature display swit-  
ches over and again displays the ACTUAL temperature in the refrigera-  
tor. The display changes from flashing to illuminated numbers.  
3
Information! When the setting is changed, the compressor does not  
start immediately if automatic defrosting is currently taking place.  
Switching the Appliance off  
0 1. To switch off, push and hold the ON/OFF button for approx. 5 seconds.  
This will result in a countdown from "3" to "1" taking place in the tem-  
perature display. On reaching "1" the fridge will switch off. The temper-  
ature display will go off.  
The appliance is only completely disconnected from the electricity  
supply when the power plug has been removed from the power outlet.  
3
Note:  
The appliance cannot be switched on or off if unplugged, or if there is  
no power being supplied to it.  
Following connection to the mains power supply, the appliance returns  
to the same operating state as before the interruption of main power.  
If the appliance is not going to be used for an extended period:  
0 1. Switch off the appliance, to do this press the ON/OFF button (see  
above).  
2. Remove the mains plug.  
3. Clean the appliance thoroughly (see section: "Maintenance and Clean-  
ing").  
4. Leave door open to avoid accumulation of odours.  
818 35 69-02/2  
17  
 
Holiday Mode  
In the holiday mode the temperature for the refrigerator is approxi-  
mately +15 °C. In the holiday mode it is therefore possible to leave the  
door of the empty refrigerator closed during periods of extended  
absence. Advantage: Unintentional closing of the door, or accidental  
closing of the door by persons who have access to your home during  
your absence, is no longer possible. Without the holiday mode leaving  
the door closed would lead to the accumulation of odours and mould.  
After emptying and cleaning the appliance, proceed as follows:  
0 1. To set the holiday mode, press the „+“ (WARMER) or „-“ (COLDER) but-  
ton.  
The temperature display will change and indicate in flashing numbers  
the DESIRED temperature that is currently set.  
2. Hold down the „+“ (WARMER) button until the temperature display  
indicates H (for holiday). The temperature shown in the temperature  
display will change in steps of 1 °C until it reaches +8 °C. After +8 °C  
the value +15 °C will appear in the display with the letter H. The fridge  
is now operating in energy-saving holiday mode.  
To switch the fridge back to normal operation, press the „-“ (COLDER)  
button.  
3
Important! Do not store any goods in the refrigerator when the holiday  
mode is in operation. The temperature is regulated at about +15 °C  
when the holiday mode is in operation. This is too warm for food pro-  
ducts.  
Opening the Door  
If the door is closed when the appliance is in operation, it cannot be  
immediately opened again, because a vacuum occurs which holds the  
door closed until pressure has been equalised. The door can be opened  
again after several minutes.  
18  
818 35 69-02/2  
 
Control and Information Systems  
The control and information systems consist of the temperature display,  
an optical warning display and an acoustic warning.  
The system warns if:  
– if the appliance door remains open for longer than 5 minutes;  
– if the temperature in the fridge compartment is too warm;  
– functional errors at the appliance.  
"Open Door" Warning  
If the fridge door is left open for longer than 5 minutes the red warn-  
ing display will flash and an acoustic warning tone will sound.  
If you need more time to load or rearrange refrigerated foods, you can  
switch off the warning tone by pressing the ALARM OFF button.  
The red warning display will go off when the door is closed.  
Temperature warning  
The red warning light flashes and a warning tone sounds, as soon as the  
temperature in the refrigerator is warmer than 12 °C. Such a rise in  
temperature can possibly be put down to:  
– opening the door a lot or leaving it open for a long time;  
– storing larger quantities of warm food;  
– a fault with the appliance.  
You can turn off the warning tone using the ALARM OFF button.  
The warning light and the warning tone switch off automatically,  
when the ACTUAL temperature existing in the refrigerator drops below  
12 °C again.  
Function Errors  
If the appliance electronics detects a technical fault that needs to be  
rectified by customer service, the temperature display shows a square in  
the upper part of the temperature display. The red warning indicator  
flashes. The appliance will continue to operate in emergency mode.  
818 35 69-02/2  
19  
 
Interior Fittings  
Storage Shelves  
The shelf in the lowest runners over the fruit and vegetable drawer  
must always remain in this position, so that fruit and vegetables stay  
fresher for longer.  
The remaining storage shelves can  
be adjusted to various heights:  
0 1. Pull the storage shelf forward until  
it can be tipped up or down and  
removed.  
2. To insert at a different height use  
the same procedure in reverse.  
Adjustment for tall items:  
0 1. Remove the front half of the two-  
part vario glass storage shelf and  
insert it at a different level. Space is  
then gained for storage of tall items  
on the storage shelf below.  
Variable Inner Door  
The door compartments can be pulled up and removed, and inserted at  
other positions as needed.  
Salad Bin  
The salad bin can be divided into  
sections by inserting the dividers.  
0 1. Insert the large divider in the mid-  
dle or to the left side of the salad  
bin as required.  
20  
818 35 69-02/2  
 
Interior Fittings  
.
The ventilation grille above the  
salad bin improves air circulation  
so that groceries keep for longer.  
3
Bottle Rack  
Place bottles in the rack with the  
bottleneck to the front.  
Important: Only store unopened  
bottles horizontally.  
The bottle rack can be tilted for  
storing opened bottles.  
0 1. To do this pull the bottle rack for-  
ward until it can be tilted  
upwards, then slide the front sup-  
port into the next level up.  
Quick Chill Shelf  
The quick chill shelf can be placed  
in one of the upper grooves. To  
maintain the best performance the  
shelf should be placed in the  
second groove from the top.  
818 35 69-02/2  
21  
 
Interior Fittings  
Bottle and Can Holder  
The side of the bottle and can hol-  
der is moveable to enable a more  
flexible placement of cans and  
bottles in front of the grid. To  
alow the holder to be moved  
easier when moving sideways,  
press the shelf backwards.  
The bottle support can be pulled  
out when chilling larger bottles.  
Dismantling of the Bottle and Can Holder  
0 1. Take out the quick chill shelf with  
holder from the cabinet.  
2. To loosen the holder from the  
shelf, bend the hooks/brackets  
that surround the backside of the  
shelf.  
Bottle Holder  
A bottle holder in the bottle compart-  
ment is used to prevent individual  
bottles from falling over and can be  
slid sideways.  
22  
818 35 69-02/2  
 
Proper Storage  
The cooling fan ensures an even tem-  
perature distribution in the fridge.  
There is a max. temperature differ-  
ence of 1 °C. Foods with different  
lengths of storage time can therefore  
be arranged on the shelves as you  
like, without having to take into  
account the different temperature  
zones which usually occur. The tem-  
perature in the fruit and vegetable  
drawer is around 3 - 4 °C higher than  
the fridge temperature set. The  
example arrangement opposite  
shows possible ways of storing food.  
The shelf immediately above the fruit  
and vegetable tray should be 5 °C for  
safe storage of meat and fish  
products. In order to check that the  
appliance is at 5 °C on the lowest  
shelf you can carry out the following  
test yourself:  
0 1. Place a cup of water in the centre of the said shelf with a thermometer  
inside.  
2. Leave the fridge door closed overnight and check the temperature first  
thing in the morning.  
3. At this point the temperature should read no more than 5 °C; if it does,  
you need to adjust the temperature to a colder setting.  
For further information on keeping food cool and safe a guide  
published by the Ministry of Agriculture, Fisheries and Food is available  
and can be obtained free of charge by contacting:  
Foodsense, London SE99 7TT. Tel: 0645 556000  
Tip: Food stored in the refrigerator compartment should always be  
covered or packed so that they do not dry out, lose their flavour, or  
transfer their flavour to any other refrigerated food. The following are  
suitable for packing:  
– polyethylene bags;  
– plastic containers with lids;  
– special plastic covers with rubber retainers;  
– aluminium foil.  
818 35 69-02/2  
23  
 
Hints and Tips  
Normal Operating Sounds  
• You may hear faint gurgling or bubbling sounds when the refrigerant  
is pumped through the coils or tubing at the rear, to the cooling  
plate/evaporator.  
• When the compressor is on, the refrigerant is being pumped round  
and you will hear a whirring sound or pulsating noise from the  
compressor.  
• A thermostat controls the compressor and you will hear a faint click  
when the thermostat cuts in and out.  
Food Storage  
To obtain the best performance from your refrigerator:  
• Do not store warm food or evaporating liquids.  
• Do not store food uncovered.  
• Keep the time between buying chilled food and placing it in your  
refrigerator as short as possible.  
• Do not push food together too much, try to allow air to circulate  
around each item.  
2 Energy Saving Advice  
• Do not install the appliance close to sources of heat, such as a cooker,  
dishwasher or radiator.  
• Locate the appliance in a cool well ventilated room and make sure  
that the air openings of the appliance are not obstructed.  
• Always leave warm food to cool down to room temperature before  
placing in the fridge.  
• Try to avoid keeping the door open for long periods or opening the  
door too frequently as warm air will enter the cabinet and cause the  
compressor to switch on unnecessarily often.  
• Ensure there are no obstructions preventing the door from closing  
properly.  
24  
818 35 69-02/2  
 
Defrosting  
The Fridge defrosts automatically  
Maintenance and Cleaning  
Before any maintenance or cleaning work is carried out DISCONNECT  
the appliance from the ELECTRICITY supply.  
Internal Cleaning  
0 1. Clean the inside and accessories with warm water and bicarbonate of  
soda (5 ml to 0.5 litre of water). Rinse and dry thoroughly.  
1 Warning!  
• Do not use detergents, abrasive powders, highly perfumed cleaning  
products, wax polishes or cleaning products containing bleach or  
alcohol.  
2. Regularly check the door seals and wipe clean to ensure they are clean  
and free from debris.  
External Cleaning  
1 Warning!  
• Do not use abrasive products  
• There are sharp edges on the underside of the product so care should  
be taken when cleaning.  
1Important: Do not use cleaning agents for stainless steel or other  
aggressive or abrasive cleaning agents. The protective coat of lacquer  
on the stainless steel surface can be damaged by these.  
The coat of lacquer protects against finger prints and therefore  
additional cleaning agents and maintenance products are no longer  
required.  
0 1. Clean the appliance with a cloth and lukewarm water. Commercially  
available dish washing detergents may also be used. Rinse and dry thor-  
oughly.  
Accumulation of dust at the condenser reduces cooling performance  
2
and increases energy consumption. For this reason carefully clean the  
condenser at the back of the appliance once a year with a soft brush or  
a vacuum cleaner.  
2. After everything is dry place appliance back into service.  
818 35 69-02/2  
25  
 
Maintenance and Cleaning  
Changing the carbon filter  
To maintain the best performance  
the carbon filter should be chan-  
ged once a year with normal  
usage.  
New carbon filters can be purcha-  
sed from your local Service Force  
Centre.  
0 1. The filter is placed behind the grill  
and can be reached by opening  
the cover. The cover can be ope-  
ned by simultaneously pressing  
the lever on the right of the grill  
(1) and pulling the cover outward  
(2).  
2. The carbon filter is then pulled  
out of its slot (3).  
3. The new carbon filter is placed in  
the existing slot.  
The filter should be handled care-  
1
fully so fragments do not loosen  
from the surface.  
Replacing the Light Bulb  
Warning! Danger of electrical shock! Before replacing the light bulb  
switch appliance off and remove the mains plug.  
1
Light bulb specifications: 220-240 V, max. 25 W, fitting: E 14  
Important!  
When replacing the lamp only fit a  
lamp of suitable diameter, that is at  
least 18 mm, this will ensure a good  
seat on the rubber seal.  
Where to purchase: specialist  
retailer or AEG Service Force Centre.  
26  
818 35 69-02/2  
 
0 1. To switch the appliance off press and hold the ON/OFF button.  
2. Unplug the mains plug.  
3. To change the light bulb, undo the  
cross head screw and remove the  
light bulb cover downwards.  
4. Change the defective light bulb.  
5. Refit the light bulb cover and the  
cross head screw.  
What to do if ...  
Before contacting your local Service Force Centre, check the following  
points.  
Symptom  
Solution  
Check there is power at the socket  
Check there is not a power cut by  
checking the household lights.  
No power to the appliance.  
Check the fuse has not blown.  
Temperature is set too cold.  
Set the temperature to a warmer setting  
temporarily.  
Appliance cools too much.  
Check the ambient temperature is within  
the appliances operating limits  
The temperature in the refrigerator is too  
high.  
Check the temperature regulator is  
turned to the correct setting relative to  
ambient conditions.  
Door is opened for longer than 5 minutes  
Warning tone sounds, red warning display Switch off the warning tone by pressing  
is flashing  
the ALARM OFF button. Do not leave the  
door open for longer than necessary.  
818 35 69-02/2  
27  
 
Symptom  
Solution  
Temperature warning  
Please look at “Temperature warning”  
section.  
Red warning light flashing, warning tone  
sounding  
There is a function fault.  
Please inform your local Service Force  
Centre. Do not open the door of the  
appliance again.  
Temperature display shows a square.  
The compressor runs continuously  
Adjust the temperature regulator to give  
correct temperature control.  
Check that the door is closed.  
Large quantities of food have recently  
been placed in the cabinet and/or door is  
frequently opened.  
Check that air ventilation is not  
obstructed.  
Ensure the bulb is correctly fitted.  
Replace the bulb if it has blown.  
The light does not come on.  
Check the door light switch is not  
jammed.  
Water drain hole is blocked.  
Water on the floor or on storage shelves. See the "Cleaning and Maintenance" sec-  
tion.  
Noise  
Refer to Normal Operating Sounds  
The compressor does not start  
immediately after changing the  
temperature setting.  
This is normal, the compressor starts after  
a period of time.  
If after the above checks there is still a fault, call your local AEG Service  
Force Centre.  
In-guarantee customers should ensure that the above checks have been  
made as the engineer will make a charge if the fault is not a  
mechanical or electrical breakdown.  
Please note that proof of purchase is required for in-guarantee service  
calls.  
28  
818 35 69-02/2  
 
Regulations, Standards, Guidelines  
This appliance was designed for household use and was manufactured  
in accordance with the appropriate standards. The necessary measures  
in accordance with appliance safety legislation regulations (GSG),  
accident prevention regulations for refrigeration appliances (VBG 20)  
and the regulations of the German Society of Electrical Engineers (VDE)  
were observed in the manufacture of this appliance.  
The refrigerant circuit has been checked for leaks.  
This appliance is in accordance with the following EU guidelines:  
;
– 73/23/EWG dated 19 February 1973 - low voltage guidelines.  
– 89/336/EWG dated 3 May 1989  
(including guideline change notice 92/31/EWG) - EMV guideline  
Technical Terminology  
Refrigerant  
Liquids that can be used to a generate a cooling effect are known as  
refrigerants. They have a relatively low boiling-point, indeed so low,  
that the warmth from the food stored in the fridge or freezer can  
cause the refrigerant to boil and vaporise.  
Refrigerant Circuit  
Closed circulation system that contains the refrigerant. The  
refrigerant circuit comprises primarily of an evaporator, a compressor,  
a condenser and pipe work.  
Evaporator  
The refrigerant is evaporated in the evaporator. Similar to all other  
liquids, refrigerant requires heat to evaporate. This heat is removed  
from the interior of the appliance, as a result the interior is cooled.  
The evaporator is therefore located inside the appliance or placed in  
foam immediately behind the inner wall and thus not visible.  
Compressor  
The compressor looks like a small drum. It is driven by a built-in  
electric motor and is mounted on the base of the appliance at the  
rear. The task of the compressor is to draw in vaporised refrigerant  
from the evaporator, to compress it, and to pass it on to the  
condenser.  
Condenser  
The condenser normally has the form of a grid. The refrigerant  
compressed in the compressor is liquefied in the condenser. During  
this process, heat is released to the surrounding air at the surface of  
the condenser. The condenser is mounted on the base of the appliance.  
818 35 69-02/2  
29  
 
Guarantee Conditions  
Standard Guarantee Conditions  
We, AEG-Electrolux, undertake that if within 12 months of the date of the purchase  
this AEG-Electrolux appliance or any part thereof is proved to be defective by reason  
only of faulty workmanship or materials, we will, at our discretion repair or replace the  
same FREE OF CHARGE for labour, materials or carriage on condition that:  
• The appliance has been correctly installed and used only on the electricity or gas  
supply stated on the rating plate.  
• The appliance has been used for normal domestic purposes only, and in accordance  
with the manufacturer's operating and maintenance instructions.  
• The appliance has not been serviced, maintained, repaired, taken apart or tampered  
with by any person not authorised by us.  
• All service work under this guarantee must be undertaken by a Service Force Centre.  
Any appliance or defective part replaced shall become the Company's property.  
• This guarantee is in addition to your statutory and other legal rights.  
• Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be  
available outside these hours in which case a premium will be charged.  
Exclusions  
This guarantee does not cover:  
• Damage or calls resulting from transportation, improper use or neglect, the  
replacement of any light bulbs or removable parts of glass or plastic.  
• Costs incurred for calls to put right an appliance which is improperly installed or calls  
to appliances outside the United Kingdom.  
• Appliances found to be in use within a commercial environment, plus those which  
are subject to rental agreements.  
• Products of AEG-Electrolux manufacture which are not marketed by AEG-Electrolux.  
European Guarantee  
If you should move to another country within Europe then your guarantee moves with  
you to your new home subject to the following qualifications:  
• The guarantee starts from the date you first purchased your product.  
• The guarantee is for the same period and to the same extent for labour and parts as  
exists in the new country of use for this brand or range of products.  
• This guarantee relates to you and cannot be transferred to another user.  
• Your new home is within the European Community (EC) or European Free Trade Area.  
• The product is installed and used in accordance with our instructions and is only used  
domestically, i.e. a normal household.  
• The product is installed taking into account regulations in your new country.  
Before you move please contact your nearest Customer Care centre, listed below, to  
give them details of your new home. They will then ensure that the local Service  
Organisation is aware of your move and able to look after you and your appliances..  
France  
Germany  
Italy  
Senlis  
+33 (0) 3 44 62 29 29  
+49 (0) 800 234 7378  
+39 (0) 800 117511  
+46 (0) 8 672 5360  
+44 (0) 8705 350 350  
Nürnberg  
Pordenone  
Stockholm  
Luton  
Sweden  
UK  
30  
818 35 69-02/2  
 
Service & Spare Parts  
In the event of your appliance requiring service, or if you wish to pur-  
chase spare parts, please contact Service Force by telephoning:  
08705 929 929  
Your telephone call will be automatically routed to the Service Force  
Centre covering your post code area.  
For the adress of your local Service Force Centre and further informa-  
tion about Service Force, please visit the website at  
Before calling out an engineer, please ensure you have read the details  
under the heading „What to do if.....“  
When you contact the Service Force Centre you will need to give the  
following details:  
1.  
2.  
3.  
4.  
Your name, address and post code.  
Your telephone number  
Clear and concise details of the fault.  
The model and serial number of the appliance (found on the  
rating plate).  
• Model Name  
• Model Number (PNC)  
• Serial Number (S-No.)  
5.  
The purchase date  
Please note that a valid purchase receipt or guarantee documentation  
is required for in-guarantee service calls.  
Customer Care  
For general enquiries concerning your AEG-Electrolux appliance, or for  
further information on AEG-Electrolux products please contact our  
Customer Care Department by letter or telephone at the address below  
or visit our website at www.aeg-electrolux.co.uk.  
Customer Care Department For Customer Service in the Republic of  
Major Appliances  
AEG-Electrolux  
Domestic Appliances  
Addington Way  
Luton  
Ireland please contact us at the address  
below:  
AEG/ Electrolux Group (Ire) Ltd  
Long Mile Road/ Dublin 12  
Republic of Ireland  
Bedfordshire, LU4 9QQ  
Tel: 08705 350350 (*)  
Tel: +353 (0) 1 4090754  
(*) Calls may be recorded for training purposes  
818 35 69-02/2  
31  
 
ïïïKÉäÉÅíêçäìñKÅçã=  
AEG Hausgeräte GmbH  
Postfach 1036  
D-90327 Nürnberg  
© Copyright by AEG  
818 35 69 – 02/2 - 0907  
Subject to change without notice  
 

8e6 Technologies Computer Hardware MSA 004 005 User Manual
Acer Computer Monitor al200 User Manual
Agilent Technologies Portable Generator 08111 90002 User Manual
Alcatel Carrier Internetworking Solutions Telephone 4008 User Manual
Alcatel Lucent Network Card VPN Firewall Portfolio User Manual
Altinex Stereo Amplifier MT113 102 103 User Manual
American Standard Indoor Furnishings 0178027 User Manual
AMX Stereo Amplifier DAS TAMP4 SIG User Manual
Atlantis Land Switch A07 ES3526VA PoE User Manual
BK Stereo Amplifier AV6000 Series II User Manual